How to calculate GOR (gas-oil ratio) in oil and gas
Last updated November 20, 2026 by WellersDen
Quick answer
Gas-oil ratio (GOR) is the volume of gas produced divided by the volume of oil produced over the same period, with the gas at standard conditions and the oil at stock-tank conditions. In oilfield units:
Both forms give the same number. A well that makes 31,500 scf of gas and 42 STB of oil during a test has a GOR of 750 scf/STB.
On this page
GOR calculator
Enter your own volumes. It runs in your browser, and the numbers you enter are not sent anywhere.
What you need to measure
- Gas volume in standard cubic feet (scf). The metered gas, corrected to the base pressure and temperature you report at. Most flow computers do this correction for you; a raw volume at separator pressure is not scf.
- Oil volume in stock-tank barrels (STB). Net oil after shrinkage and after the water in the oil stream has been taken out. A separator meter reading in barrels is not STB yet; see stock tank barrel vs barrel.
- The same interval for both. Gas and oil must cover exactly the same hours of the test.
Worked example
Assumptions: a 6-hour test through a three-phase separator. The gas meter total is already corrected to 14.696 psia and 60 °F. The oil volume is net oil at stock-tank conditions. The well is flowing naturally, so no lift gas is in the gas stream.
- Gas produced: 31,500 scf
- Oil produced: 42 STB
Step 1: divide gas by oil
Step 2: check it against the daily rates
The test duration cancels out, which is why GOR can be taken from volumes or from rates. If the two answers differ, the gas and oil figures do not cover the same interval.
Step 3: convert if the report needs other units
Units and conversions
- scf/STB is the usual oilfield unit. Some reports use Mscf/STB, where M means thousand (and MM means million).
- m³/m³ is the metric unit. 1 scf/STB = 0.1781 m³/m³, and 1 m³/m³ = 5.615 scf/STB.
- That conversion is purely geometric. Metric standard conditions are usually 15 °C and 101.325 kPa, not 60 °F and 14.696 psia, so an exact conversion between reporting systems also adjusts the gas volume for the change of base.
Which GOR are you calculating?
"GOR" is used for several different quantities. A report should say which one it means.
Produced GOR
Gas over oil for a test or a day of production. This is what the formula above gives, and what a well test measures. It is also called producing or instantaneous GOR.
Solution GOR (Rs)
The gas dissolved in the oil at a given pressure and temperature, from a PVT study. It is a fluid property, not a production measurement. While reservoir pressure is above the bubble point and no free gas is flowing, produced GOR should sit close to the initial solution GOR (Rsi). Below the bubble point, free gas flows as well and produced GOR usually climbs above Rs.
Cumulative GOR (Rp)
Cumulative gas produced divided by cumulative oil produced since first production.
Separator GOR and total GOR
Conventions vary here. A well test normally meters the gas leaving the separator. More gas comes out of the oil on the way down to stock-tank pressure, and that tank vapour is often not metered. Total GOR is separator GOR plus stock-tank GOR. If only separator gas was measured, say so, because the figure understates the total.
What the number tells you
GOR is a quick indicator of fluid type. McCain's widely quoted rules of thumb put black oils below roughly 1,750 to 2,000 scf/STB of initial producing GOR, volatile oils from there to about 3,200 scf/STB, and gas condensates above that. These are guides only; a PVT analysis decides the fluid type.
The trend matters more than a single value. A GOR that holds steady and then rises test after test points to the reservoir dropping below its bubble point, or to gas from a gas cap reaching the well.
Common mistakes
- Mixing up GOR and GLR. Dividing gas by total liquid (oil plus water) gives gas-liquid ratio, which is lower than GOR in any well that makes water. See GOR vs GLR.
- Using bbl where STB is needed. Oil at separator conditions still holds gas and occupies more volume, so dividing by it gives a GOR that is too low.
- Being out by a factor of 1,000. Gas in Mscf divided by oil in STB gives Mscf/STB. Multiply by 1,000 for scf/STB.
- Counting lift gas. On a gas-lifted well the separator meters injected gas too. Subtract the injection volume before calculating GOR.
- Mismatched intervals. A 24-hour gas total over a 6-hour oil volume is not a GOR.
- Not stating the base conditions. Regulators and contracts use different pressure bases, such as 14.65, 14.696, 14.73, or 15.025 psia. The same gas reported at 14.65 psia instead of 15.025 psia is about 2.6% larger, and so is the GOR.
- Reporting a GOR with no oil. If no oil was produced the ratio is undefined. Report it as N/A, not as zero.
FAQ
What is the formula for GOR?
GOR (scf/STB) = gas volume in standard cubic feet / oil volume in stock-tank barrels, with both volumes covering the same period. Dividing the gas rate by the oil rate gives the same result.
What units is GOR measured in?
Usually scf/STB in oilfield units and m³/m³ in metric units. Some reports use Mscf/STB, where 1 Mscf is 1,000 scf. 1 scf/STB is 0.1781 m³/m³.
What is a normal GOR for an oil well?
There is no single normal value; it depends on the reservoir fluid. As a rule of thumb, black oils start below roughly 1,750 to 2,000 scf/STB, volatile oils run up to about 3,200 scf/STB, and gas condensates are higher. The trend from test to test usually says more than one reading.
Is GOR the same as solution gas-oil ratio (Rs)?
No. Solution GOR (Rs) is the gas dissolved in the oil at a given pressure and temperature, measured in a PVT study. Produced GOR is gas over oil at the surface. They are close only while the reservoir is above its bubble point and no free gas is being produced.
How do I convert GOR from scf/STB to m³/m³?
Multiply by 0.1781. For example, 750 scf/STB is about 133.6 m³/m³. This is a geometric conversion and does not adjust for the different standard conditions used in metric reporting.
Get GOR with the rest of the well test
WellersDen takes the test duration and the oil, gas, and water produced, typed in or imported from a CSV file, and returns GOR together with the daily rates and water cut. The results, formulas, and assumptions go into a PDF report you can send to a client. The calculator is free and needs no account. A free account includes one PDF report.