BS&W vs water cut: what each one measures
Last updated November 20, 2026 by WellersDen
Quick answer
BS&W (basic sediment and water) is the percentage of water and solids in a sample of oil, usually found by spinning the sample in a centrifuge. Water cut is the percentage of water in all the liquid a well produces, free water included.
BS&W describes a sample of the oil stream. Water cut describes the well. On a well tested through a three-phase separator, an oil-leg BS&W of 2% can sit alongside a water cut of nearly 39%, as the example below shows.
On this page
Comparison table
| BS&W | Water cut | |
|---|---|---|
| What it measures | Water plus sediment in a sample of oil or emulsion | Water as a share of the total liquid the well produces |
| Formula | BS&W (%) = (Water + sediment in sample) / Sample volume × 100 | Water cut (%) = Water volume / (Oil volume + Water volume) × 100 |
| Units | % by volume | % by volume, or a fraction |
| How it is obtained | Centrifuge test on a sample (ASTM D4007 / API MPMS 10.3 in the lab, API MPMS 10.4 in the field) | Metered or gauged oil and water volumes over a test, or a water-cut or multiphase meter |
| Free water | Normally excluded: the sample is taken after the separator has removed it | Included |
| Sediment | Included | Not included |
| When to use it | Oil quality, sales and pipeline specifications, correcting a metered oil volume to net oil | Well performance, allocation, surveillance, lift and facility design |
Where each one comes from in a well test
A three-phase test separator splits the well stream into gas, oil, and free water. The free water leaves through the water leg and is metered. The oil leg is metered too, but that oil still carries some emulsified water, and a sample from it goes to the centrifuge. That reading is the BS&W.
The BS&W then moves water from the oil column to the water column:
BS&W is written as a fraction in these formulas (0.02 for 2%). Strictly, the reading includes sediment as well as water. In most production samples the sediment is a small part of it and the whole reading is treated as water. If the solids are significant, measure water separately, by distillation or Karl Fischer titration.
Worked example
Assumptions: a 12-hour test through a three-phase separator. To keep the example about water, the oil-leg volume is taken as already corrected to stock-tank conditions (see stock tank barrel vs barrel for that step). Sediment in the sample is negligible.
- Water-leg meter: 180 bbl
- Oil-leg meter: 300 bbl
- Centrifuge BS&W of the oil-leg sample: 2%
Step 1: split the oil leg
Step 2: total the water
Step 3: water cut
Step 4: daily rates
Three different numbers could be reported from this one test:
- 2% is the BS&W of the oil leg. It is not the well's water cut.
- 37.5% is what you get by ignoring the BS&W and using the two meter readings as they are. It is close, but it overstates the oil by 6 bbl.
- 38.75% is the water cut.
The formula on its own, with WOR and oil cut, is covered in water cut formula.
When the two terms are used for the same thing
Usage varies, and it is worth asking what was actually measured. Where a well is tested through a two-phase separator, or sampled at the wellhead, there is no separate water leg. The water fraction of a full-stream liquid sample is then used as the water cut, and some operators call that number BS&W.
That works only as well as the sample. Free water drops out in the sample line and the bottle, slugging wells give a different answer every few minutes, and the centrifuge reading still includes sediment. A report that says which stream was sampled, and how, avoids the argument later.
BS&W as a sales specification
Pipelines and buyers set a maximum BS&W for the oil they accept. The limit is set by the pipeline tariff or the sales contract, commonly somewhere between 0.5% and 1%. Oil above the limit is treated again before it is sold. This is the BS&W of treated oil at the point of sale, and it says nothing about the water cut of the wells behind it.
Common mistakes
- Treating the centrifuge BS&W as the well's water cut. On a three-phase test it leaves out all the free water.
- Not moving the BS&W water out of the oil. The oil rate ends up too high and the water rate too low.
- Forgetting the dilution. When the sample is cut 50:50 with solvent, the tube reading has to be doubled unless the tube is graduated to read percent directly.
- Skipping heat or demulsifier. A tight emulsion does not break in the centrifuge, and the water still held in the emulsion layer goes uncounted.
- Relying on one spot sample from a well that is slugging or was only just put on test.
- Deducting BS&W twice, once in the flow computer or net-oil computer and again by hand.
FAQ
Is BS&W the same as water cut?
Not in general. BS&W is the water and sediment in a sample of oil. Water cut is water as a share of all the liquid the well produces, including free water. They are close only when the sample represents the whole liquid stream, such as a full-stream sample with no free water removed.
What does BS&W stand for?
Basic sediment and water. It is also written BSW, and API standards use the term sediment and water (S&W).
How is BS&W measured?
Most often by centrifuge: a measured sample is mixed with solvent, usually with demulsifier and heat, spun in graduated tubes, and the water and sediment at the bottom is read off. ASTM D4007 (API MPMS Chapter 10.3) is the laboratory method and API MPMS Chapter 10.4 the field method. Water alone can be measured by distillation or Karl Fischer titration.
How do I calculate water cut from BS&W in a well test?
Multiply the oil-leg volume by the BS&W fraction to get the water carried in the oil. Add it to the free water, subtract it from the oil, then divide total water by total liquid. With 180 bbl of free water, 300 bbl through the oil leg, and 2% BS&W, the water cut is 38.75%.
What BS&W is acceptable for selling crude oil?
It depends on the pipeline tariff or sales contract. Limits commonly fall between 0.5% and 1%. Check the specification that applies to your delivery point.
Once you have net oil and total water
WellersDen does not apply the BS&W correction for you; it expects net oil in STB and total water in bbl. From those, the gas volume, and the test duration it returns the daily rates, water cut, and GOR, and puts them in a PDF report with the formulas and assumptions stated on it. The calculator is free and needs no account. A free account includes one PDF report.